<img src="http://mutable-instruments.net/forum/uploads/2DXW7WQ8JAP1.jpg" alt="Mutable instruments' users community" />

i have a bad contact on ic4 thank you ,i don’t understand i’s the third socket with bad contact commanded to Reichelt ;thank you olivier !!!

Comment by oliv June 2012 permalink

oupps i don’t have see

Comment by oliv June 2012 permalink

thank’s olivier i check all this point

Comment by oliv June 2012 permalink

where i can find the schematic of filter ?

Comment by oliv June 2012 permalink

i have sand down a lot but no all is ok i can’t wait 15j or more for receive the box . but i need continue to inspect when i have the time before mounting my two other kit

Comment by oliv June 2012 permalink

i have testing in all direction ,then i have the time i try another kit

Comment by oliv June 2012 permalink

not just one case 3 case in glossy paper yes

Comment by oliv June 2012 permalink

i have lot of problem with my last command on my three shruti kit , i have talk about this to pichenette ,and when i could i post photos (before i have mounted 3 shruti with no problem with the box ) it’s near 3 mm of difference with the cente…

Comment by oliv June 2012 permalink

lfo speed

the only risk i have if i change the code it’s bug on starting i can’t burn the Atmega ?

Comment by oliv June 2012 permalink

lfo speed

how to program ,i need interface ,sorry i’m the noob of the noob :)

Comment by oliv June 2012 permalink

lfo speed

modify the code yes i need two years for unerstanding the first line :))) slow slow slow ,for meditation ,shruti tanpura !!!!

Comment by oliv June 2012 permalink

lfo speed

do you think it’s possible to hack with a ltc1799

Comment by oliv June 2012 permalink

lfo speed

a damnnnnn !!!! hahahah i need my modular

Comment by oliv June 2012 permalink

"Audio Input" to "CV1 Output"

thank you pichenettes i really cool to know ,we can use cv safe with other analog gears !

Comment by oliv June 2012 permalink

simple mods for effect

terrible way , hahaha i’m not engineer ,i don’t know the schematics and i don’t found it ,i have lot of difficulty to read the layout ,and i just find something by hazard when i have make the checking test for my problem before on resonnance . …

Comment by oliv June 2012 permalink

"Audio Input" to "CV1 Output"

hello and what i possible to do for use this mods correctly with protection ?

Comment by oliv May 2012 permalink

fixed the problem it’s on the lm13700 i have changed them and no working yahhhhhhhhhhhhhhhhhhhhhhhh

Comment by oliv May 2012 permalink

There should be an audio signal corresponding to increasingly filtered versions of the oscillators signal on pins 14, 1, 7, and 8 of the TL074. Is that the case? i hear signal on each pin The signal at pin 7 of IC4 should be silence when resonan…

Comment by oliv May 2012 permalink

Put the pole selector to 4 pole, since resonance is more emphasized in 4-pole mode. ok i have tested ,in two position Have you adjusted the resonance trimmer? Is it correctly soldered? i think i have a problem with us ,no click at the end whe…

Comment by oliv May 2012 permalink

ok thank you component side: http://www.flickr.com/photos/69546228@N05/7308106408/ solder side: http://www.flickr.com/photos/69546228@N05/7308104018/in/photostream/

Comment by oliv May 2012 permalink

i have found the trimer was out of order ,i have changed for à 10k and now the screen work fine but i have a problem on the smr4 board ,the reso i really low and impossible to push up the filter for screaming … i search from where is commi…

Comment by oliv May 2012 permalink

thank you pichenettes ,sorry for this misunderstanding the number was not correct for the atmel 4th to 24 on atmel 6th to 25 … 11th to 26 12th to 27 13h to 28 14th to 29 15th to 68 ohm resistor (and after go to 30th pin on atmel) the …

Comment by oliv May 2012 permalink

somes picture here : http://www.flickr.com/photos/69546228@N05/sets/72157629975786620/

Comment by oliv May 2012 permalink