Tom

Computer Recording Setup? Dual boot?
or just use a computer with no windows at all, replaced by a brilliant working setup under Linux…Tango Studio for example (but there are dozen of linux distros !)

Comment by Tom May 5 permalink
My project: Boomtrapped
Here comes a teaserof an audio creation for a french public institution. The goal was to make song mixing sound field recordings of public libraries atmospheres and sounds and electronic music. The tune is finished and lasts 5min 15sec. It will b…

Comment by Tom May 4 permalink
DIGI FX board troubleshooting
btrd:/home/tom/Shruthi/DigiFX/2013/shruthi-1# make -f dsp/makefile hex returns make: *** Pas de règle pour fabriquer la cible « hex ». Arrêt. Anyway, I’ve downloaded http://mutable-instruments.net/static/firmware/dsp_01.hex, flashed it on my …

Comment by Tom April 3 permalink
DIGI FX board troubleshooting
Yesterday, I’ve downloaded the master branch on github (after posting the message sck10). I followed all the instructions given in the firmware section of the shruthi page. Then when located in the root directory I tried “make -f dsp/makefile b…

Comment by Tom April 3 permalink
DIGI FX board troubleshooting
Chip inserted backard: I don’t think so. ISP pin one is connected to 328 PIN 18. The “detrompeur” looking towards IC5 label and leds Cable plugged backwards: nope, the programmer is flashing orange if I try to connect it the other possible way on…

Comment by Tom April 3 permalink
DIGI FX board troubleshooting
I’m surely missing something obvious…..

Comment by Tom April 3 permalink
DIGI FX board troubleshooting
avrisp mkII

Comment by Tom April 3 permalink
DIGI FX board troubleshooting
All traces are fine between the isp pin connector and the corresponding legs of the 328p Just to be sure….I don’t need to plug the mobo if I want to talk with my 328p, do I ?

Comment by Tom April 3 permalink
DIGI FX board troubleshooting
Hi all ! Well, no shorts between the isp pins, and 4,97V when checking VCC on pin 7 of the 328p… What could be wrong then ?

Comment by Tom April 3 permalink
DIGI FX board troubleshooting
Ok, i’ll try this when coming back home

Comment by Tom April 3 permalink
DIGI FX board troubleshooting
Yep, the programmer led turns green when connected to the isp pins of the digifx board…something else us going wrong on the board. Could a faulty quartz prevent the programmer to talk to the 328

Comment by Tom April 2 permalink
DIGI FX board troubleshooting
What could be the reason there is no communication between the ISP pins and the atmega even if conitnuity if fine between those ISP pins and the atmega ? I tried to talk to my arduino UNO with the programmer, it’s fine, when I place the arduino’s…

Comment by Tom April 2 permalink
DIGI FX board troubleshooting
Using avrdude -V -p m644 -C /etc/avrdude.conf -c avrispmkII -P usb -B 10 for checking the m644 chips of other shruthis let me think my 328p is dead as it doesn’t respond (with the exact same programmer setup) to the command avrdude -V -p m328p -C /…

Comment by Tom April 2 permalink
DIGI FX board troubleshooting
Ok, when trying to flash the 328p with my avrisp mkII using the make -f dsp/makefile bake, I get this error: echo “sck 10\nquit\n” | /usr/bin/avrdude -V -p m328p -C /etc/avrdude.conf -c avrispmkII -P usb -e -tuF avrdude: stk500v2_command(): co…

Comment by Tom April 2 permalink
DIGI FX board troubleshooting
Ok thanks, I’ll try this then !

Comment by Tom April 1 permalink
DIGI FX board troubleshooting
Due to the way it was built, there could have been a short between 2 of the 8 pins connecting the two boards. - Theres continuity between the two boards on all the 8 connecting pins – I reheated and added some solder on all joints of the filter …

Comment by Tom April 1 permalink
DIGI FX board troubleshooting
What could be the reason no led are lightened (especially the red one)? I’ll have a scope tomorrow, what should I see when checking the 328p pins ? How can I check my 328P is fried or not ? Cheers, Tom.

Comment by Tom April 1 permalink
DIGI FX board troubleshooting
It has worked for 1 year and a half with no problem…let’s check with another one….No change… What’s bothering me is that none of the 2 leds are lighten….

Comment by Tom March 31 permalink
DIGI FX board troubleshooting
Reheated all the joint of the digiFX filter board…still no led lighten…. Coul a shortcut, due to manipulation, have fried the 328p ?

Comment by Tom March 31 permalink
DIGI FX board troubleshooting
Ok, let’s try to reheat all solder joints then. !

Comment by Tom March 31 permalink
My project: Boomtrapped
Some Wwork in progress ….No mastering, rough mix… what do you think of this beginning tune ?

Comment by Tom February 11 permalink
Age Question
33 today…not the younger, but not the older too ;-)

Comment by Tom February 7 permalink
[SOLD]Selling my DSI tetra
@jimi23: I have to say I didn’t really had the time to get deeply into the beast. Some musical projects arrived before I could make my hand on it. But I’m really sure it has some nice sounds to produce (I heard some tetras during live gigs and they…

Comment by Tom December 2012 permalink
Mutable 8tracks mix
Correct for Boomtrapped ! Thanks rumpelfilter !

Comment by Tom December 2012 permalink
My project: Boomtrapped
Glad you like it ! I decided, for the upcoming tracks to simplify things….The “kind of messy” things in the older tracks came from the fact that I used only mono synths and thus was thinking I had to play a lot of notes to “fill” the tune… Now …

Comment by Tom December 2012 permalink
My project: Boomtrapped
U.S.O First complete song using my Ambika + 2 SMR4 + MS-20 Hope you’ll like it !!

Comment by Tom December 2012 permalink
2000
Great news ! I couldn’t think so many Shruthis had been sold….on the other hand, it’s such a killer beast I should not be surprised ! Good job Olivier, keep it this way !

Comment by Tom November 2012 permalink
Soundcloud groups
Only sounds of the beasts ? or can I put some boomtrapped tracks ?

Comment by Tom November 2012 permalink
My project: Boomtrapped
Hy guys ! here are some news from boomtrapped. I’m working on my scenography right now, and I will be using 3D modeling in the videos I’ll use. As usual, I’m using free softwares…For the 3D, it’s Blender 2.63 As an exercice, I made a (simple) t…

Comment by Tom November 2012 permalink
Mutable 8tracks mix
Great !

Comment by Tom October 2012 permalink

More Comments

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: Tom
Joined: January 2011
Visits: 65
Last Active: 8:10AM
Roles: Member